Design Engineering
- Civil, foundations, drains, rooms, structure
- Mechanical, tanks, structure, supports
- Electrical, load calculations, panel wiring, circuit designing
- Biogas to Electricity Power Generation project design & development
SERVICES
Civil Construction
- Excavation
- Piling works
- Formwork
- Steel cutting, bending and fixing
- Concrete works
- Backfilling & compaction
- RCC / PCC flooring
- Drain works
- Stone pitching and soling
- Pits & Dykes
- Paving
- Block Masonry
Mechanical Construction (Fabrication & Erection)
- Process and Utility piping
- Cooling Tower / spray pond
- Overhead cranes / Gantries
- Boiler, Vessels and columns
- Fire Fighting & Sprinkler Systems
- Fuel storage stations / depots
- Heavy equipment erection
- Chimney / Exhaust system
- Structure works and sheds
- Storage tanks and reaction vessels
- Heat exchangers
- Duct and insulation works
- Pumps & Blowers
- HVAC Systems
- Conveyor Belt systems
- Other miscellaneous mechanical works
Electrical Works
- Installation of Transformers, DBs, MCC Panels
- Electrical and Process equipment
- Power and Control cabling
- Fabrication and erection of cable trays
- General electrical wiring, conduiting
- Panel wiring
- Cable testing
Biogas to Electricity Generation Plants
- Construction of Anaerobic Digesters
- Piping
- Upgradation Unit
- Raw, Low pressure and High Pressure gas storage tanks
- Cooling Systems
- Gas Analyzer
- Dehydration Units
- De-watering system
- Rotary Dryers for Compost
- Gas Compressor
- Gas Pressure regulation system
- PLC and SCADA control and Monitoring system
- Gas Generators
- Power Synchronization
OUR MISSION & VISION
Creating a Purpose Today to Shape Tomorrow
01
- FRP Lining is resin lining to raise durability and safety by Lining inside of concrete tank with FRP (Fiberglass Reinforced Plastics). It provides strength and is not affected by structural Cracks which occur on the concrete tank.
Our FRP lining services are below.
- Supply & Fixing of FRP
- FRP coating on structure &
- FRP coating inside Drain Chanel &Chemical
- FRP coating of PVC/cPVC
02
- Rubber Lining is an application method used to protect multiple Types of systems by lining corrosion and abrasion-resistant Rubber upon the surface or inside of pipes and tanks.
- Rubber lining inside vessel,
- Rubber lining inside piping &
03
- Core Drill is a drill specifically designed to remove a cylinder of material much like a hole The material left inside the drill bit is referred to as the core. Core drills used in metal are called annular cutters. Core drills used for concrete are generally called Diamond Core Drills and are water cooled.
- Core cutting work up to 500mm long.
- Core cutting for connection making from Cooling tower
- Core cutting work for Anchor Bolts
- Dowell anchoring and chemical bolts fixing
04
- Non Shrink Grouting
Non-Shrink Grout is a hydraulic cement grout that, when Hardened under stipulated test conditions, does not shrink, So its final volume is greater than or equal to the original Installed volume. It is often used as a transfer medium Between load-bearing members.
- Pump / Blower skid grouting
- Base plate grouting
- Anchor bolts fixing with
05
- Epoxy Work
Epoxy coatings are formulated based upon the performance Requirements for the end product. When properly catalyzed And applied, epoxies produce a hard, chemical and solvent
Resistant finish. They are typically used on concrete and steel
To give resistance to water, alkali and acids.
- Chemical pits,
- Pump casing for sea
- Sea water tank &
06
- Painting & Sandblasting.
Paint: - A colored substance which is spread over a surface and dries to leave A thin decorative or protective coating. We deal in all kinds of paints.
- Epoxy
- Enamel
- High Temperature
- Weather Shield (Cement Surface Paint).
All type of paints used in different projects, especially DFL, OPRl,, Neoplex etc.
Sandblasting:-Roughen or clean (a surface) with a jet of sand driven by compressed air.
Sandblasting & epoxy painting at HOM structure.
Sandblasting & epoxy painting at NEOPLEX structure.
07
- Insulation Work
Insulation, or more correctly thermal insulation, is a general term used to describe products that reduce heat loss or heat gain by providing a barrier between areas that are significantly different in temperature.
We have the ability to fix the all types insulation, on piping, tanks, tracing with G.I & Aluminum cladding.
- Glass wool & Rockwool
- Thermo pore
- Polyurethane (PUR and PU) insulation
08
- Heat Tracing
We deal in supply and installation of two types of heat tracing:
- Steam tracing is heat tracing performed by circulating Steam around process pipes to heat them. Steam tracing Is normally installed on: Stagnant piping sections such as Branch connections from parallel heat exchangers or pumps Bypasses around equipment.
- Electric heat tracing, heat tape or surface heating, is a system Used to maintain or raise the temperature of pipes and Trace heating takes the form of an electrical heating element Run in physical contact along the length of a pipe.
- Steam & electric heat tracing on caustic
- Steam heat tracing on reaction vessel.